How to remove rust from a necklace

This blog post will answer the question, “How to remove rust from necklace” and cover topics like how to get rid of rust on a necklace, how to remove rust from silver jewelry, and frequently asked questions.

How to remove rust from a necklace?

Rust from the necklace can be removed by following the steps given below:

  • Line a dish with aluminum foil to clean a rusted necklace. 
  • 1 cup boiling water, 1 tsp baking soda, and 1 tsp salt are combined in a bowl. 
  • Then, submerge your necklace in the solution for 10 – 15 minutes. 
  • Your necklace’s corrosion and tarnish will be removed by reacting with aluminum foil and baking soda.

Methods of removing rust from the necklace

Rusted or tarnished jewelry might seem drab and unappealing compared to fresh jewelry. Rust appears reddish and flaky and is most often seen on costume jewelry, while patina appears dull and is most commonly found on silver jewelry. You may clean your tarnished or rusted necklace with a few cleaning products you likely already have in your house and keep it looking beautiful all night.

Method No 1:


  • 1 cup (240 mL) white vinegar in a mixing bowl White vinegar is a natural cleaning solution that is moderately acidic, but not to the point of causing damage to your necklace. 
  • Put some into a big enough basin or shallow dish to accommodate your necklace. White vinegar may be found at most home goods and supermarket shops. Costume jewelry is unaffected by vinegar, but expensive metals and stones may be damaged. Vinegar is effective in removing corrosion, but not so much at removing tarnish.
  • Submerge your necklace entirely in vinegar. Make sure all pieces of your necklace, particularly those with corrosion, are submerged in the vinegar. If necessary, apply additional vinegar until your necklace is completely saturated.
  • Set aside your necklace for at least 8 hours. Vinegar takes a long time to dissolve the rust on your necklace. Place your bowl somewhere safe where it won’t be bothered overnight, and check on it the next morning. 
  • Warning: If you leave the bowl in the sun too long, it can heat up the vinegar.
  • Using a toothbrush, scrub the rust away. Remove your necklace from the vinegar and place it on a cloth. Gently scrub the rust off your necklace with a toothbrush until it is clean. 
  • If your necklace has a lot of corrosion on it, soak it for an additional 1 to 2 hours. The gentle bristles of a toothbrush will not harm your jewelry.
  • Using cold water, wash your necklace. To avoid breaking down portions of your necklace, make absolutely sure all of the vinegar is gone.
  • To clean any places that were very rusted, concentrate the water on them. Warm water is worse on your jewelry than cool water.
  • Using a clean towel, pat your necklace dry. Before wearing or storing your necklace, make sure it is totally dry. If you get your necklace wet, it may corrode again. To avoid scratching your jewelry, use a soft towel.

Method No 2:


  • 1 cup (240 mL) warm water with 2 drops of dish soap Mix warm water from the sink with little mild dish soap in a small basin. To maintain the surface of your necklace, try to use odorless, dye-free dish soap.
  • Tip: Dish soap is mild on jewelry and does not react chemically. It’s great for non-tarnished necklaces or those that are metal-plated rather than totally metal.
  • Using your fingers, rub your necklace in soap and water. Make sure your necklace and chain are completely immersed in the water. Massage the pendants and chain surfaces gently to remove any corrosion or tarnish.
  • Using your fingertips instead of a cloth or sponge, which may harm delicate jewelry, is more gentle.
  • Warm water should be used to rinse your necklace. To avoid black stains on your necklace, make absolutely sure there is no soap trace left on it. 
  • Clean any additional tarnished spots with warm water. Dry dish soap might discolor and make your necklace seem patchy.
  • Using a clean towel, pat your necklace dry. Before you use your cloth, make sure it is entirely clear of dirt and debris. Before putting your necklace away, gently pat it dry and make sure it is completely dry.
  • If you keep your necklace damp, it will rust or tarnish faster. If your necklace is silver, polish it using silver polish to keep it sparkling.

Method No 3:


  • Aluminum foil should be used to line a small basin. Keep the foil’s shiny side facing up. Choose a dish that can accommodate roughly 1 cup of liquid (240 mL).
  • Aluminum foil causes an electrolytic reaction that removes tarnish and rust from the necklace without hurting the metal.
  • 1 tbsp (14 g) baking soda, 1 tbsp (14 g) table salt, 1 tbsp (14 g) warm water In the microwave, heat 1 cup (240 mL) warm water until it is warm but not boiling. 
  • Pour the water into the foil-lined basin, then whisk in the baking soda and sodium chloride until they are fully dissolved.
  • Baking soda is a somewhat caustic natural cleaning agent. It can take care of tarnish on gold and silver, as well as rust on steel and costume jewelry.
  • Immerse your necklace in the mixture, making sure it comes into contact with the foil. Insert your necklace in the bowl with care, as the water will still be hot. Make sure the necklace is in contact with the foil at the bottom of the basin.
  • Set aside the necklace for two to ten minutes. You may need to leave your necklace for the whole 10 minutes, depending on how corroded or rusted it is. 
  • Small bubbles may appear on your necklace as a result of the chemical reaction that is eliminating the rust. After 2 or 3 minutes, if your necklace isn’t too rusted, you may remove it.
  • Using cold water, rinse your necklace. Remove your necklace from the hot water with tongs and rinse it in the sink with cold water. 
  • Make sure there’s no salt or baking soda residue on your necklace so it doesn’t remain there for too long. To get rid of your baking soda and salt solution, pour it down the drain.
  • Using a clean towel, pat the necklace dry. Place your necklace on a flat towel and carefully fold it over to pat it dry. 
  • To avoid rust, let the necklace out to air dry for 1 hour before storing it again, or wear it right away to enjoy its fresh, shining appearance. When necklaces are kept in a damp or humid setting, rust forms.
Materials Needed
Baking soda
Dishwashing soap

What Causes Jewelry to Rust?

Rust is caused by the following factors:

  • Moisture
  • Acids
  • Oils
  • Air

It’s simple: your jewellery gets exposed to moisture, acids, oils, and air over time. They interact with the metal in the jewellery, causing it to rust and finally wear out. This is due to moisture and sulphur in the air interacting with the metal.

It is impossible for pure gold and silver to corrode. However, both silver and gold jewelry can corrode, and will most likely do so over time, so knowing how and when to maintain your items is critical. In principle, pure gold jewelry should never corrode, but as we all know, gold jewelry is usually always combined with another metal to make it stronger.

Because gold does not combine with oxygen, it does not corrode. If you choose a coated gold chain for men, however, there is a potential that your jewelry can rust or corrode over time. There’s no need to be concerned, my chums. It’s natural for gold-plated jewelry to tarnish over time, which is why it’s less expensive than real gold. 

The gold plating may start to peel away, exposing the metal behind, which is prone to corrosion, or the metal beneath may interact with the environment despite the gold covering it. You may avoid these problems by carefully cleaning and preserving your jewelry.

How to Get Rid of Rust on Jewelry?

Rust can be removed from jewelry by following the guidance given below:

  • Use salt with baking soda
  • Use Vinegar
  • Use Dishwashing Soap

Use salt with baking soda

If you discover that some of your jewelry is starting to corrode and you’re wondering how to eliminate corrosion off jewelry, there are a few options. Sodium bicarbonate and salt can be used to scrub away some of the corrosion without harming the chain’s metal. This is how you do it:

  • Make sure the shiny side of the aluminum foil is facing up when covering the interior of a bowl.
  • Then, in a separate bowl, warm up one cup of water (but not to boiling) and pour it in. Add one teaspoon of sodium bicarbonate and one teaspoon of salt to the mixture.
  • Fill the dish with your jewelry. As the aluminum foil soaks, each piece of jewelry must be in contact with it.
  • Allow it to sit for five to ten minutes, based on how rusted the item was, before rinsing it with cold water.
Materials Needed
Baking soda
Aluminum foil

Use Vinegar

Vinegar is another common home substance that can be used to prevent corrosion, but it won’t assist with tarnishing. For that issue, you’ll need to utilize a different cleaning procedure. Vinegar has the potential to harm certain gemstones and valuable metals, so do your homework before using this procedure. The four simple stages are as follows:

  • In a basin, pour one cup of vinegar
  • Add your gold chains and earrings to the mixture.
  • Allow for a few minutes to many hours of sitting time, depending on how rusted the parts are and what materials they’re composed of. 
  • Check your jewelry to see if the corrosion is starting to come off if you’re unsure how long it will take.
  • Use cold water to rinse and a gentle cloth to dry.
Materials Needed
Soft cloth

Use Dishwashing Soap

Dish soap is one of the most popular ways of cleaning jewelry and eliminating corrosion because it is simple and inexpensive. Here’s what you should do:

  • In a bowl, combine one cup of warm water and 2 drops of dish soap, ideally odorless.
  • Add your jewelry to the water and scrape hard-to-reach areas with your fingertips or a soft toothbrush.
  • In a separate dish of warm water, wash the soap from your jewelry. Then dry with a clean cloth.
Materials Needed
Dishwashing soap
Soft cloth

Frequently Asked Questions(FAQs), “How to remove rust from a necklace?”

How do you get the rust off of jewelry?

To make a thick paste, use equal amounts of toothpaste and bicarbonate soda. After that, apply this mixture to the rusted area and let it sit for 10 minutes. Scrape the area with a scrubbing pad or a toothbrush to eliminate any remaining rust. After that, wash and dry the clothes in cold water.

How do you get the rust off cheap jewelry?

Toothpaste is the greatest rust-removal DIY jewelry cleaner, and it’s simple to use. Take an old toothbrush and coat it with toothpaste. Cover your jewelry completely with the coating and then rinse it in a cup of water. Using a towel, dry your object.

Can toothpaste get rid of rust?

Did you know toothpaste may help you get rid of rust stains? Put to the material with a moist cloth and massage in, then rinse before washing. Alternatively, apply toothpaste to corrosion spots on silverware or tools, wait 10 minutes, then wash away. The white, non-gel type is the most effective.

Does vinegar remove rust?

White vinegar may be used to effectively remove corrosion. Rust interacts with vinegar and eventually disappears. To eliminate rust from a rusted metal item, immerse it in white vinegar for a few hours and then wipe it clean. Alternatively, you may clean the item with a towel soaked with white vinegar.

Can Coke remove rust?

What is it about Coca-Cola that makes it such an efficient cleaner? Coca-Cola is carbonated, allowing it to destroy metal oxides and remove corrosion on a wide range of metals and alloys. Its rust-busting ability is aided by phosphoric acid, while its stain-removing ability is aided by citric acid.

Does Coke remove rust from jewelry?

Silver is a popular metal for jewelry and tableware. If you don’t have access to a chemical cleaner, Coca-Cola, or Coke, may be used to clean sterling or coated silver. Coke’s acid acts to remove any dust or corrosion from the silver’s surface.


Leave a Comment